Why Pro-Deck?

Phases of Screening

When the material hits the screen deck it goes through three phases from the feed to discharge points.

 

Rollover a hotspot for the definition of that stratification situation.

What Stratification Situation Are You Experiencing?

Screening Finished Early

Screening process finished early

Situation

When screening is finished early, it is completed within the first 1/3 of the deck and under size particles have passed the media openings.

Risk

Losing out on the maximum potential of the screen media.

Pro-Deck Solution

Your Pro-Deck specialist will focus on a screen media blend that improves the overall wear life of your screen deck and maximize the screening surface. You may see a slight reduction open area, but the opening will remain the same and the extended wear life will increase your up-time, production rates and profits.

Screening Process Not Completed

Screening Process Not Completed

Situation

Screening is not complete because undersized particles are going over the discharge end.

Risk

Carry over and contaminated material.

Pro-Deck Solution

In this situation, your Pro-Deck specialist will look at maintaining the opening while increasing your open area.  We will consult you in choosing the right screen media blend that will increase the number of openings where necessary without sacrificing the overall wear life of the deck.  Your product quality will increase without affecting your overall operating expenses.

Optimal Screening

Optimal Screening

Situation

Most screening is complete approximately 2/3 of the way down the deck. Near size particles utilize the last 1/3 of the deck to find an opening.

Risk

Even though the full deck is being used, the potential of your screen media is not being maximized.

Pro-Deck Solution

While the quality of your final product might meet specification, you may still be able to optimize your screen media. Your Pro-Deck specialist will consult you on a screen media blend to add wear life at the feed end while increasing open area where it is most critical at the discharge end.  Your screen will operate longer without interruptions, allowing you to make your product within specifications at a higher profit.

Pro-Deck Success Stories

Taylor, B.C. Company Shakes Out Efficiency, Profitability With Haver & Boecker Screen Media System

 

In the fast-moving oil and natural gas fields of the Peace River Region in northeastern British Columbia, downtime means lost opportunity and profit. Efficiency and optimal uptime are especially crucial for Nels Ostero, which is home to six vibrating screens: two 6-by-20 horizontal screens, a 6-by-20 incline scalping screen, a 6-by-16 inclined splitting screen, and two 7-by-16 washing screens. With such a wide array of machines from different manufacturers, Nilson Ostero, manager of the sand and gravel company, says selection of high-quality, long-lasting screen media is especially important.

 

The now third-generation company has several different types of screen media. But Ostero said change-outs were required too often on the feed end of the washing screens in particular, as much as four or five times per year for each screen. Plus, change-outs on the washing screens are more time- and labor-intensive than on any of the other screens. The feed end of a washing unit can take four employees up to two shifts to complete. That’s a $3,000 expense in labor alone.

 

With varying output rates, two 10-hour shifts of downtime can be crippling, easily costing the company more than six figures per change-out. It was an expense and hassle Ostero figured he’d have to live with.

 

Then Haver & Boecker came calling.

 

Markus Kopper, general manager at Haver & Boecker Rocky Mountains, contacted Ostero and set up a site visit to perform a complete vibration analysis, which is a part of Haver & Boecker’s Pro-Deck approach. Among other recommendations, Kopper recommended changing screen media on 22 of the 34 sections of deck in the operation to fix problems with blinding, pegging, open area and excessive wear.

 

At the time of the analysis, Ostero had Ty-Wire on the first two sections of the top deck on both screens. Ty-Wire, which is a blend of polyurethane and wire cloth, has a greater open area than traditional modular polyurethane, and the material offers 4 to 6 times the wear life in comparison to woven wire cloth. The screens at the discharge end were regular square mesh.

 

Kopper said Ostero would benefit from tailoring the first section of the decks to the application and phase of screening. They needed more wear resistance and could reduce the open area to get a larger impact surface for the material. The change had the potential to significantly reduce the downtime. Kopper recommended swapping out the first section of Ty-Wire to Ty-Max with the same size opening. Ty-Max screen media is manufactured with polyurethane that is specially formulated for optimum wear resistance. This media handles direct feed better than wire cloth, reduces change-outs and maximizes productivity – exactly what the operation needed.

 

Because this meant reducing the open area to get a larger impact surface, Kopper recommended screen media on the remainder of the deck that would balance open area to successfully complete the sizing of materials. Ty-Wire provides better wear life than wire cloth while allowing for more open area. Cobra Vibe self-cleaning screens provide maximum open area while preventing blinding or pegging.

 

Soon after the change-outs, Nilson said downtime for screen change-outs had been cut in half. He predicted the Ty-Max would last a couple of seasons. While Ty-Max reduced open area on the feed end, the Cobra Vibe provided more open area at the discharge end. This blended solution gave Ostero the optimal combination of open area, durability and productivity.

wstyler-ostero
Professional Blending of Screen Media Delivers in Quality and Profits

 

They say good things come in threes. In the case of screening for mining and quarry operations, profit comes in three distinct phases: layered, basic and sharp screening. But how good they are – whether they maximize efficiency and improve the potential for success – depends on having the right screen media on the deck for each of the three phases.

 

A relatively new method for achieving that goal is a blended screen media approach that incorporates the ideal screen media for each phase and the ideal mix of media for the process overall. The goal in implementing a blended solution is to find the optimal combination of open area and durability. Hit the sweet spot and you’ll maximize product quality and profits by increasing efficiency of classification while minimizing downtime and maintenance costs.

 

 

Three Distinct Phases and Outcomes

During the first phase of screening, the layered phase, a deep bed containing coarse and fine particles hits the screen at the feed end of the deck. In the basic phase, the particles begin to stratify as fine material settles at the bottom and larger material climbs to the top of the bed. The sharp phase occurs toward the discharge end of the deck. It’s during this final phase that the near-size particles move into direct contact with the screen media and have the last opportunity to fall through the openings.

 

There are typically two scenarios mines and quarries want to avoid when it comes to screening.

 

The first situation is the result of a deck that completes screening too early. In this scenario, particles travel only about a third of the way down the deck until all the undersize material has passed through the openings. While the main mission – classifying the material – is still achieved, the entire deck isn’t being used to its full capability. The results are diminished profits from premature screen media wear.

 

Consider this example: An operation produces 400 tons an hour and charges $10 per ton. Due to high abrasion, the media with high open area wears out quickly and needs to be replaced after only two weeks of operation. Replacing the top deck takes two people roughly four hours. At about $4,000 an hour of product not being processed and sold, that screen change-out costs $16,000 in lost revenue alone.

 

The second scenario involves screening that does not finish completely. In this case, undersized particles travel over the discharge end and contaminate the material. This can double a company’s production cost if the material needs to be re-screened, not to mention the lost efficiency and time. And if the material ends up too contaminated to be sold, profitability is lost altogether. In the worst-case scenario a company may not recognize it is producing contaminated product, which can lead to costly warranty claims and negative image.

 

Consider this example: The same operation produces 400 tons an hour and it costs the company $6 per ton to produce the material. Due to insufficient open area at the discharge end of a vibrating screen, the media does not allow the near-sized material to pass. As a result, the final product is contaminated and must be reworked. This means that the company needs to rework its material for a total cost of $12 per ton. With a sales price of $10 per ton, the company is losing $800 per hour until all of the material is re-processed.

 

A possible third scenario, optimal screening, is the ultimate goal of every operation. The bulk of undersized material passes through the openings about two-thirds of the way down the screen deck and the last third of the deck allows all the near-sized particles to find an opening. The final product meets specification and can be sold for top dollar. However, while a company is often satisfied with achieving optimal screening, it seldom recognizes the potential to increase profits even further.

 

Consider this example: The same operation produces 400 tons an hour and charges $10 per ton. Its screening is considered optimal and it is producing high quality product. Due to greater impact at the feed end of a vibrating screen, the screen media at that end wear out sooner than the remaining panels and need to be replaced. Replacing the first section takes two people roughly one hour. At about $4,000 an hour of product not being processed and sold, that screen change-out costs $4,000 in lost revenue.

 

In all three scenarios, the key to achieving the most profitable screen surface is finding the right balance between wear life and open area – the amount of open space on a screening surface. Increasing open area normally leads to a decrease in wear life while reducing open area usually increases the wear life of the screen media.

 

 

A Professional Approach

Customized solutions that blend screen media types on the same deck ensure the longest product life, limit downtime and maximize profit potential. A professional analysis will determine the right combination of open area and wear life appropriate for each of the three phases of screening. But determining the ideal blended media solution requires much more than trial and error. It requires a trained professional to delve into the numerous intricacies that impact the bottom line.

 

A professional specializing in optimized screen media generally follows five integral process steps, which can be applied to deck types using tensioned screen sections or modular screen panels:

 

1. Vibration Analysis
Using a wireless tool specifically designed for vibrating screens, the professional can detect faults and conduct measurements of the machine’s dynamic operating conditions. Prior to making any changes to the screen media, the measurements are imported to a computer system that uses a tuning wizard to optimize mechanical performance through recommended machine settings.

 

2. Machine Inspection
The results of the vibration analysis also build the foundation for a complete machine inspection of body components, the suspension system and wear parts. Special attention is given to screen media supporting parts such as bar rails, rail liners and tension rails.

 

3. Screen Media Audit
A complete review of the current screen media setup is conducted. Using a consultation guide, the audit will take the phases of screening into account while evaluating material characteristics and overall product quality. The professional will also examine environmental factors, screen condition, signs of premature failure and any blinding and pegging occurring. Blinding happens when moist granules fill the opening and clog the screen surface, while pegging refers to aggregates mechanically lodged in the opening of a screen.

 

4. Screen Media Recommendation
The results of the vibration analysis and the screen media audit build the framework for the screen media recommendation. Recommendations will be based on the correct balance between performance and durability, while catering to the appropriate phase of screening. The professional will recommend screen media technology based on categories such as anti-pegging and anti-blinding characteristics, open area and wear life. All recommendations should be visualized using computer software that allows for the personalized configuration of a deck.

 

5. Screen Media Implementation
After all recommendations are discussed and a solution is agreed upon, the final process of implementation can begin. Implementing the blended screen media gradually, by replacing one screen section at a time allows the professional to monitor the levels of production and effects of the adjustments. With each change, production rates and final output qualities are evaluated to ensure the screen media combinations are becoming more efficient. This process is continued until the best possible results have been achieved. It’s all about making modifications for better ROI — using the proper media for each phase of your unique screening operation.

 

 

Screen Media Options

Whether feed materials are wet, dry or exceptionally abrasive, selecting the correct screen media is the key to a professionally blended deck. Open area and wear life requirements are different during the individual phases, requiring a unique approach to each.

 

The market boasts numerous screen media options, and each offers a unique set of features for individual applications. Some of the most effective products that professionals may consider during their blending approach are the following:

 

  • Polyurethane
    Among the more durable materials used in screen media, polyurethane provides a long wear life with little maintenance. The flexible polymer is resistant to tears and abrasion, while premium polyurethane products also offer tapered openings that reduce blinding and pegging. This makes the material a good choice in higher wear areas in both wet and dry applications, but these positive characteristics traditionally come at the expense of open area.

 

  • Woven Wire
    At the other end of the spectrum is woven wire. It is commonly referred to as wire cloth or wire mesh screen and it comes in a variety of alloys, weave types and diameters. Woven wire offers some of the greatest open area and can be used for a wide range of applications. It also is known to make the “cleanest” cut when referring to accuracy. These strong advantages come at the expense of wear life, but fortunately not all woven wire is the same. When selecting woven wire, it is critical to insist that the wire be very high in carbon content to allow for optimum characteristics in tensile strength and ductility. This high quality alloy can only be achieved by drawing the wire using a patented process.

 

  • Hybrid Screens
    The newest screen media technology is hybrid screens. Hybrid screens combine the excellent wear life characteristics of polyurethane with the great open area of woven wire cloth. This combination lasts up to six times longer than traditional wire cloth but offers as much as 80 percent more open area than modular polyurethane. The hybrid’s tapered openings either accept or reject near-size material to provide a self-cleaning effect, which eliminates nearly all blinding and pegging. The result is a screen that is extremely durable and highly productive.

 

  • Self-Cleaning Screens
    Self-cleaning screens combine individual wires using flexible polyurethane strips, allowing the wires to move at frequencies higher than the G-force generated by the vibrating screen and eliminating blinding and pegging. The unique design of flat lying wires even offers higher open area than woven wire, while outlasting it by up to 25%.

 

 

Proof of Profit

For a company in Madoc, Ontario, about three hours northeast of Toronto, Canada, implementing a customized blend of screen media positively impacted the operation immediately.

 

Danford Construction Ltd. has been a family business for more than 50 years. Its Aggregates Division handles a variety of materials in a granite quarry, two limestone quarries, a traprock quarry and eight gravel pits. In 2011, Danford called in Haver & Boecker as a consultant to help customize screening for its granite operation. Following vibration analysis, Danford customized its deck with the ideal blend of screens. “We are getting eight times the wear life out of the new screen set-up, adding two weeks production time per year, and have reduced our screening costs by 75% as a result”, said Jamie Danford, owner of Danford Construction, Ltd.

 

Danford and other companies have learned that expert guidance and fully customized configurations can pay for themselves in the short-term and dramatically increase profitability over time. From extended screen life and less downtime for change-outs to a greater amount of a higher quality product, companies that deploy a smart blend of screen media can maximize performance in each phase of screening.

wstyler-danford